Friday, January 23, 2015

Day 6: Drilling Holes!

    Ok, I was not looking forward to day 6! I knew I had 16 holes to drill and I knew it would not be easy.
Picture laying on cold concrete trying  to put pressure on a drill to go through hardened steel! Not fun at all.

    I got a little excited and burned out the drill bit I had so I had to go buy another. I picked up a really good bit for hardened steel and a few others just in case.

    Drilled out the 16 holes to mount the hangers and that's about it. It took some time and elbow grease but I got it. Tomorrow I hope to re mount the springs and work on the pinion angle.

Had to turn the front bolts opposite because a body mount was in the way!


     I had to unbolt and drop the rear shackles to get to the bolts so I could remount just the shackles. I could not get to the inner shackle bolts wit the spring mounted up.




         Some of the best investments you can make! One battery charge took out all 16 holes!



        Save your drill bits and get some of this! A shot of lube will keep your drill bit from getting hot and going dull!





     I hope to remount everything tomorrow and try and set the pinion angle. After that, ... clean up the rear and paint the axle. I will still need to find a professional welder for the spring perches. I could do it but I fear it would be a mess LOL

Thursday, January 22, 2015

Day 5: Mockup Madness

     1.  I will cut off the original spring pads and grind the area smooth.
     2.  Locate the mounting position for the new pads. 5-7/16" from brake backing plate
     3. Mount the springs onto the axle in approximate location
     4. Grind off original driver side spring hangers
     5. Put it all back under the car and mark the new hanger locations
     6. Mark and drill new holes for the hangers and install.
     7. Check and adjust for proper pinion angle
     8. Once in position, spot weld the spring pads.
     9. Remove rear and springs for permanent welds
    10. Clean and paint
    11. Mount rear to car.

     Started the day removing the one new hanger I had mounted on Day 1. Then I mounted the springs to the axle and rolled it all back under the car.



    After some hanger position swaps, some loosening of the springs, shoving, pulling, banging etc I finally got the hangers in position and the drive shaft connected.  This took a lot longer than I expected. It would have went a lot faster with another person.






    Tomorrow I will start out removing the springs from the hangers and pull the rear out again leaving the hangers clamped in position. I will then drill out the mounting holes and bolt them in place. Then the rear goes back under to fine tune the location of the spring perches/pads. The tricky part will be setting the pinion angle while the rear is off the ground without a load. I will probably just firm everything up but leave it just loose enough where I can reposition the rear if needed  while the car is sitting back on the ground.

Wednesday, January 21, 2015

Day 4: Back To The Grind

    I got a late start but I managed to get the drivers side hangers knocked off. I also got the emergency brake brackets off. I did not have a good flap disc so I used a DeWalt grind wheel and it worked very well.

    First I ground down the rivet heads flush with the hanger.





 
    Then I mark and drill a relief hole.






    Once I drilled all of the holes I just knock them off with a hammer.




    Since I may not be using the original hokes I just ground everything flush and left it like that. I did not get a picture of that. Maybe I will add them in tomorrow. I will clean up and paint the orignal brackets to preserve them. Most likely they will end up on eBay.

    Tomorrow I will start mocking up the rear. I am crossing my fingers the hanger move wont run into any issues.

A refresher.....

     1.  I will cut off the original spring pads and grind the area smooth.
     2.  Locate the mounting position for the new pads. 5-7/16" from brake backing plate
     3. Mount the springs onto the axle in approximate location
     4. Grind off original driver side spring hangers
     5. Put it all back under the car and mark the new hanger locations
     6. Mark and drill new holes for the hangers and install.
     7. Check and adjust for proper pinion angle
     8. Once in position, spot weld the spring pads.
     9. Remove rear and springs for permanent welds
    10. Clean and paint
    11. Mount rear to car.


Tuesday, January 20, 2015

Cut Off: Day 3 _ The Rear.

    I wish I had more to report but today I only had time to cut and grind off the original spring perches.




    Tomorrow I hope to grind off the old hangers and start mocking it up!

    In the meantime, it's all I can do to not think about wire wheeling the entire rear to prep for paint! Just degrease, wash, and paint! Just degrease, wash, and paint! Just degrease, wash, and paint!

Monday, January 19, 2015

Rear End Makeover: Day 2: Starting Over

    Let's recap the things that needed attention:

        1. Axle sat too far back on the spring. About 4-5 inches off center. (wheel set nice in the wheel well)

        2. Stock spring pads too far outward to line up the new springs with the frame rails.

    These two things alone are enough to start over. I pulled the rear out from under the car today and spent the rest of the day planning and taking measurements.



    This is the approximate location of the new pads. You can see the springs would have missed the channel in the existing pads. The reason the old springs fit, they were narrrow and I believe tilted slightly to hit the channel in the pad.


Looks like they put some new brake parts in. I won't need to do much here. The existing brake lines look like they wee bent by hand and not very well at that, so I will probably replace them. If not now, later.



Here is my list in a nutshell....

     1.  I will cut off the original spring pads and grind the area smooth.
     2.  Locate the mounting position for the new pads.
     3. Mount the springs onto the axle in approximate location
     4. Grind off original driver side spring hangers
     5. Put it all back under the car and mark the new hanger locations
     6. Mark and drill new holes for the hangers and install.
     7. Check and adjust for proper pinion angle
     8. Once in position, spot weld the spring pads.
     9. Remove rear and springs for permanent welds
    10. Clean and paint
    11. Mount rear to car.

    I may need to grind rivets and remove the original parking brake brackets. I am thinking the hangers will shift to the back about 4-6 inches and that falls right at the brake brackets. Currently there is no parking brake on the car, so this will not be an issue, just more work!

   I think tomorrow I will focus on cutting off the existing pads from the rear. By the way, the rear weighs a ton! It's going to be interesting getting it all back under the car!

Sunday, January 18, 2015

Rear End Makeover: Day 1

    Well I am finally getting back in the garage.

    The car would bottom out with weight in the trunk or a person in the back seat so I was leaning towards replacing the springs. The shocks look new so it has to be the springs, right?

    Anyway I ran across a guy on facebook who offered up a kit for a 49-54 Chevy so I sent him the cash. The kit arrived so time to tear down the rear.

   I got the car up on stands and printed out the directions from Chassis Engineering. The guy states the kit is from them. Well right off I notice none of the parts look like the ones in the directions or the web photos of their kit. The bracket holes do line up so I proceeded.

    Here is a link to the kit Chassis Engineering lists for 49-54 Chevy. LINK

    Here are the directions they sent me...






Here is what they show on their site...



    I received everything in the above photo except the shock mounting bar and the shocks. The shocks were not part of the agreement and he says the kit did not come with the shock bar since the shocks for 50 Chevy mount to the bottom of the trunk floor (that's how they are on my car). I can live with that as long as the kit works. Here are the components I have...


Rear hanger with shackle

Bottom plate and bottom shock mounting

Front hanger
So lets get started.....

Here a view of how it was set up when I got it. Original springs and hangers but a different rear and pads.




    I was going to try and do this without removing the rear. I unbolted the shock and spring hangers and removed the spring.

The cardboard was to deflect sparks away from the gas tank.


 Then I used a flap disc on my grinder and ground down the factory rivets. Once I had them flush with the hanger I drilled a relief hole in the center of each rivet and tapped them out. Over all an easy job.






    So right away I have my first problem. The directions specifically tell you how to mount the hangers based on the shape of the ones in their kit, which is different than the ones I have. After playing with the passenger side front hanger I found they could only be mounted one way and match the holes. If you tried to mount the one for the drivers side it would be a totally wrong angle. So no problem. First one one. Like the directions say, only three holes match up and you have to drill the third. This told me the kit must at least be for my car.




   I attached the spring by looking at the picture in the directions. One eye curls down and one up. You can see the one closest to the front of the car has the eye turned up. Also the two spring retainers/clamps(?) compared to only one towards the back.


No problem, yet.



    But there is one that I am going to have to deal with. The center spring bolt is not going to line up with the center of the axle. The spring that was on it did not either but that one fell just in front of the pad and did not cause an issue. I have never done this kind of job before so I am not sure how to handle it yet. If I move the axle forward a little the drive shaft will then be too long and the tire would not sit center in the wheel well like it does currently. Also if I do line it up with the spring bolt , I will have to take the bolt out and flip it because currently the nut is on top and is too big for the hole in the pad??


 The other side has a round cylinder for a head and it fits in the hole.



    I decided not to worry too much about it until I get the rear hanger on. Another problem I thin I am going to run into is the new spring does not seem to line up in the existing spring pad on the axle. The original spring seemed to hit center of it but this one seems to hit off center. It is possible the rear could have shifted but I doubt it. I will have to do some measurements tomorrow and see whats going on. I may have to cut off the pads and use the ones that came with the kit. Not fun!



    By the way, the rear I have appears to be a GM 8.5-inch 10-bolt or GM Commercial. I have no idea what it came off of. The guy I got it from said it was a 3.73:1 geared posi but I have not confirmed that yet. You can find a 10-bolt 8.5-inch differential in any of these cars or trucks:



1971-'76 Chevrolet full-size cars
1994-'96 Impala
1971-'81 Buick full-size cars
1973-'77 Buick Gran Sport
1972-'77 Pontiac GTO and Le Mans
1970-'81 Chevy Camaro and Z28
1970-'81 Pontiac Firebird
1971-'77 Olds Cutlass and F-85 and Pontiac Grand Prix
1971-'79 Chevy II, Nova, Buick Skylark and Olds Omega
1973-'77 Chevelle, Malibu and El Camino
1971-'77 Pontiac Ventura and Phoenix
1971-'81 Pontiac Bonneville
1973-'77 Monte Carlo
1973-'77 Buick Apollo, Regal and Century
1980-'94 Chevy ½-ton and ¾-ton pickups
1977-'94 GMC Jimmy and Chevy Blazer


A 10-bolt front axle was used on GM 4WD vehicles as well. It was available in three ring gear choices. Axle codes were GU6 (3.43:1) GT4 (3.73:1) and GT5 (4.10:1). You can find a front 10-bolt in these trucks: 


1977-'87 K and V-series half- and three-quarter-ton Chevy pickups
1977-'91 Jimmy and Blazer 4WD
1988-'97 K1500 and K-2500 pickups 

    OK, back to the job... I moved on to the rear hanger. I ground those rivets and removed the hanger. I had a little more trouble getting to these with my grinder. Between the exhaust pipe and spare tire well, there was not much room to maneuver! Once off, again I had trouble with the directions. I can not use their description because mine look different. How they are mounted will determine the location of the shackles. One way sets it back further than the other. I will have to play around with it and see what happens. Also only two holes line up with my hanger and the directions kind of match that. They are not real clear on that.




I ran out of time so I cleaned up the garage and put everything away.



 

Monday, August 25, 2014

Some Wiring and a Mystery Noise

    I played around with the car a while today. Spent most of the time wiring up the AMP gage. I am not sure I did it right but it is definitely doing something now. I ran (looking at the back of the gage) the ignition wire to the left side of the gage and the right side over to the battery terminal on the headlight switch. When I start the car the needle goes negative a bit. When I turn on the headlights it goes up to about the middle. I have no idea if this is how it should be acting. The more amps the car draws the further into the positive it will go? I will leave it like this for now and see how it acts.

    I also removed the cigarette lighter to clean it up. I noticed a broken hot tab inside so I will probably just get a replacement. I hope to retain the original knob/lighter. I did wire it up and try to get it hot but no go .. only got a spark now and then due to the old wire.

    I also shot some video to capture the trans noise I am hearing. I am still trying to figure out what is causing the clacking sound at low speeds.


 00:00 to 00:26 Is stationary moving through the gears.
00:26 to 00:46 is reverse (no noise)
00:47 to 00:57 Is the first time you hear it but not very well
1:28 to 1:42 Is stopping and taking off at a stop sign
2:43 I drop it into first and you can really hear it.


I took the car to a transmission shop and they found nothing wrong with the trans and had no answer for the noise.  The shop has been around since the mid 70's and it's just a trans shop.


If you can offer info on the AMP gage or the noise, please comment. Or, head over to my thread on the HAMB and post there .... LINK LINK LINK